Your Plumbing Crash Course: A Guide to Bathtub Installation
Your Plumbing Crash Course: A Guide to Bathtub Installation
Blog Article
What are your beliefs on How to Install a Bathtub Yourself?
Mounting a tub isn't specifically rocket science, but it does call for solid plumbing, woodworking, and also sometimes, tiling abilities. Changing an old bathtub with a new one is also a moderately difficult task. If the old tub is easily accessible, the job can move easily; if you need to open a wall surface to eliminate the old bathtub and place the new bathtub, the task is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will need an assistant to leave the old tub and also embeded in the new one. Make sure you have actually qualified on your own for the task and also are comfortable trying it. Rather than working with a specialist to take over a halfway-completed project, it is better to think about utilizing one prior to you start. Chances are you might require an expert plumber to make tube connections.
This write-up will aid you install a new tub in your washroom if you have actually already gotten a brand-new bathtub and also do not need to change the arrangement of your previous water pipes.
Your devices and product checklist must consist of the following:
Planning for the Installation
First of all, the supporting framework provided with the bath must be fitted (if called for) according to the maker's guidelines. Next off, fit the taps or mixer to the tub. When fitting the tap block, it is essential to make certain that if the faucet includes a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bath, it is likewise sensible to fit a supporting plate under the faucets system to prevent stress on the bathtub.
Fit the flexible faucet connectors to the bottom of both taps utilizing 2 nuts as well as olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet through the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Make certain you utilize every one of the supplied washers.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom must currently be ready to be suited its last placement.
Removing Old Taps
If you require to change old taps with new ones as a part of your installation, then the first thing you should do is disconnect the water supply. After doing so, turn on the faucets to drain pipes any type of water remaining in the system. The process of getting rid of the existing faucets can be quite bothersome due to the limited accessibility that is commonly the case.
Make use of a basin wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the taps. Have a fabric all set for the remaining water that will come from the pipelines. When the supply pipes have actually been eliminated, use the very same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary taps from transforming during this procedure. Once the faucets have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned of any old sealing substance.
Prior to moving on to fit the new taps, compare the pipe connections on the old taps to the new taps. If the old taps are longer than the new taps, then a shank adapter is required for the new taps to fit.
Installing the Bathtub
Using the two wooden boards under its feet, position the bathtub in the needed setting. The wood boards are valuable in equally spreading out the weight of the bathtub over the area of the boards instead of focusing all the weight onto four tiny factors.
The following goal is to make certain that the bath tub is leveled all round. This can be achieved by examining the level as well as adjusting the feet on the bathtub until the spirit level reads level.
To install faucets, fit all-time low of the outermost versatile tap adapter to the appropriate supply pipeline by making a compression sign up with; after that do the exact same for the other tap.
Turn on the water supply and check all joints and brand-new pipework for leakages as well as tighten them if necessary. Fill up the bath tub as well as also inspect the overflow electrical outlet and also the regular electrical outlet for leakages.
Finally, repair the bath paneling as explained in the producer's user's manual. Tiling as well as sealing around the tub ought to wait up until the tub has been used at least when as this will certainly resolve it into its final placement.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will require a plastic port to prevent damage to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end gives a link to the current supply pipelines.
If you need to fit a monobloc, after that you will certainly need decreasing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, position the faucet in the mounting opening in the bath/basin guaranteeing that the washing machines remain in location in between the faucet and the sink. Protect the faucet in place with the producer supplied backnut. As soon as the tap is securely in place, the supply pipelines can be attached to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with normal tap ports. The former type ought to be linked to the tap ends first, tightening only by hand. The supply pipes can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bathtub
In the location where the bathroom satisfies the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is very important as the installation can relocate enough to split a stiff seal, triggering the water to pass through the wall surface in between the bath and the tiling, bring about issues with dampness as well as possible leaks to the ceiling listed below.
You can select from a selection of coloured sealants to assimilate your fixtures and also fittings. They are offered in tubes and also cartridges, and can securing gaps as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with spins of drenched paper or soft rope. Remember to always fill up the tub with water prior to securing, to permit the activity experienced when the bathtub remains in use. The sealer can break relatively very early if you do not think about this movement before sealing.
Alternatively, ceramic coving or quadrant tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are also conveniently readily available on the market. It is recommended to fit the tiles making use of water-resistant or waterproof sticky and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I have been very inquisitive about A Step-by-Step Guide to Installing a Bathtub and I'm hoping you enjoyed reading the entire blog entry. Sharing is caring. One never knows, you will be helping someone out. Thanks so much for going through it.
We're here for you, dial! Report this page